露天爆破智能设计系统开发及应用

为了提高露天台阶爆破设计的规范化、便捷性，对露天台阶爆破设计系统进行了开发研究。以Visual C++为开发平台，软件采用MFC框架，结合OpenGL三维引擎开发技术，实现软件从底层自主开发生态的建立。通过现场工程实践应用表明爆破设计人员可以轻松通过本系统实现三维环境下的布孔设计和爆破网络设计以及精确的GPS布孔，并取得了良好的爆破效果，提高了台阶爆破的设计质量和设计速度。爆破智能设计系统能够实现矿山爆破设计的数字化、科学化、自动化和高效化，对于露天爆破具有十分重要的意义。     

基于DEM的振动筛筛孔形状对潮湿原煤筛分效果影响的研究

随着原煤含水量的增加,引起原煤颗粒间相互粘聚,影响振动筛筛分效率。基于离散元法,运用EDEM软件模拟了潮湿原煤颗粒在圆形筛孔、方形筛孔和矩形筛孔的筛分过程,并且以筛分效率和阻碍粒排出率为衡量指标,对振动筛筛孔形状影响潮湿煤筛分效果进行了研究。结果表明:在筛孔名义尺寸相同的情况下,潮湿煤在矩形筛孔筛面上的筛分效果最好,方形筛孔次之,圆形筛孔最差。     

机加工孔套管抗挤压强度有限元分析

套管屈服强度直接影响套管抗挤压性能，套管在加工孔过程中可能诱发孔眼附近材料发生金属相变，导致套管屈服强度不再均匀分布，进而影响套管抗挤压强度。在相同工况下，对比了P110完整套管和机加工孔套管的抗挤压强度，以此为参照组分析了相变区域面积和相变区域屈服强度对机加工孔套管抗挤压强度的影响。结果表明，机加工孔会改变材料屈服强度，进而影响套管抗挤压性能。随金属相变区域屈服强度减小，机加工孔套管抗挤压强度减弱；当金属相变区域屈服强度增大时，机加工孔套管抗挤压强度增强。且机加工孔套管相变区域面积对机加工孔套管抗挤压强度的影响随相变区域屈服强度增加而逐渐削弱。     

抽采孔液态CO2预裂效果显微CT实验研究

为研究液态CO2预裂爆破后,煤体内裂隙发育情况,采用高精度微焦点显微CT系统,对预裂后不同区域的煤样进行CT扫描,并利用Photoshop进行孔裂隙占比统计学分析。研究结果显示,距预裂孔4 m处的煤体裂隙发育明显,孔裂隙占比增加了一倍,而在5 m处的煤体裂隙则发育较弱。表明抽采孔内采取液态C2预裂技术后,4 m范围内的煤体裂隙得到了充分发育,为瓦斯抽采提供了有利条件。     

冷却塔内气流流场特性研究及应用

冷却塔是火力发电厂循环水系统的重要设备,冷却塔的冷却效率对机组的微增功率有着比较重要的影响,冷却效率的提高有助于节约发电能耗。冷却塔的效率与其空气动力特性有着紧密的联系,本文以华电集团江苏分公司望亭发电有限公司3号机冷却塔的节能改造为例,研究了冷却塔内气流流场的特性,并阐述了针对该特性采取的技术措施在冷却塔优化改造中的应用实践。     

考虑水平（切向）位移影响的垫层孔隙内土工膜顶胀

The common cushion layer used in the geomembrane face rockfill dam is made of granular materials such as gravel and non-fine concrete where bulge deformation or failure of geomembrane is very likely to occur in its surface holes. The curve intersection method based on the thin film theory is the common method used to analyze the bulge deformation of the geomembrane in the surface holes of cushion layer. However, it is inaccurate due to the neglection of horizontal (tangential) displacement of the geomembrane. Based on the FEM theory, a new method is proposed, which takes the horizontal (tangential) displacement of geomembrane into consideration, and is validated by the bulge tests on the geomembrane in a circular hole. The deformations and strains of the geomembrane in different shapes of holes are analyzed by this method, and different strain distributions and failure modes are obtained. The curve intersection method is also used to compare with the new method under the same condition. It is indicated that there is less difference in the deformation and average strain of the geomembrane when the water pressure is low. However, when the water pressure is relatively high, the influences of horizontal (tangential) displacement of the geomembrane on its strain should not be neglected.     

Temperature-dependent ambipolar electrical characteristics of pentacene-based thin-film transistors: The impact of opposite-sign charge carriers

The temperature-dependent electrical and charge transport characteristics of pentacene-based ambipolar thin-film transistors (TFTs) were investigated at temperatures ranging from 77 K to 300 K. At room temperature (RT), the pentacene-based TFTs exhibit balanced and high charge mobility with electron (μ_e) and hole (μ_h) mobilities, both at about 1.6 cm²/V s. However, at lower temperatures, higher switch-on voltage of n-channel operations, almost absent n-channel characteristics, and strong temperature dependence of μ_e indicated that electrons were more difficult to release from opposite-signed carriers than that of holes. We observed that μ_e and μ_h both followed an Arrhenius-type temperature dependence and exhibited two regimes with a transition temperature at approximately 210–230 K. At high temperatures, data were explained by a model in which charge transport was limited by a dual-carrier release and recombination process, which is an electric field-assisted thermal-activated procedure. At T < 210 K, the observed activation energy is in agreement with unipolar pentacene-based TFTs, suggesting a common multiple trapping and release process-dominated mechanism. Different temperature-induced characteristics between n- and p-channel operations are outlined, thereby providing important insights into the complexity of observing efficient electron transport in comparison with the hole of ambipolar TFTs.     

Anchoring single Pt atoms on hollow Ag3VO4 spheres for improved activity towards photocatalytic H2 evolution reaction

The high cost of noble metal catalysts has been a great bottleneck for the catalyst industry. Using the noble metal at a single-atom level for catalytic applications could dramatically decrease the cost. The impacts of single Pt atoms on the photocatalytic performance of Ag₃VO₄ have been investigated and reported. In this report, single Pt atoms were anchored on the surface of Ag₃VO₄ (AVO) as a cocatalyst, and the resultant composite photocatalyst has been studied for photocatalytic H₂ production from water driven by visible light. The as-prepared AVO particles are hollow nanospheres in the monoclinic phase with a bandgap of 2.20 eV. The light absorption edge of AVO/Pt is slightly red-shifted compared to that of the pristine AVO, indicating more visible light absorption of AVO/Pt. The XPS peaks of Ag, V, and Pt exhibit a significant shift after AVO and Pt get into contact, suggesting the strong interaction between the surface Ag and V atoms, and single Pt atoms. After 3-h illumination, the photocatalytic H₂ evolution amount from AVO/Pt is improved up to 1400 μmol, which is 2.8 times that on the bare AVO. Such efficient photocatalytic H₂ evolution on AVO/Pt is still maintained after five reaction cycles. The better photocatalytic performance of AVO/Pt has been attributed to the more efficient visible light utilization and the lower interfacial charge transfer resistance, as demonstrated in the DRS and EIS spectra. The presence of the surface Pt atoms also leads to a higher amount of reactive radicals, which could efficiently promote the surface redox reactions.     

破损水文观测孔涌水封堵技术在高河矿的应用

针对高河矿奥灰水文观测孔空水管锈蚀断裂漏水严重的问题,分析了存在的问题,制定了钻孔涌水封堵技术方案及相应的注浆施工工艺,并进行了为期7天的井下试验。封堵注浆压力达到6 MPa,使用注浆水泥50 t,水泥浆液凝固良好,注浆阀门打开后无出水现象。     

大涡模拟Smagorinsky模型用于磨粒流精密加工喷嘴的质量控制研究

为研究固液两相磨粒流加工喷嘴小孔过程中的流场分布、涡旋形成规律及涡旋的存在对磨粒流加工的影响机制，采用Smagorinsky亚格子模型对磨粒流加工喷嘴小孔的流道进行大涡数值模拟，并使用磨粒流对变直径喷嘴工件进行加工试验。数值模拟发现磨粒流流体中磨粒与壁面的碰撞与剪切作用随流体的速度增大而增大，同一截面的速度存在速度差，其中还伴随涡旋的存在；通过试验研究发现：经固液两相磨粒流加工后的喷嘴小孔表面质量得到明显提高，喷嘴经过四次不同入口速度的磨粒流加工后大孔处表面粗糙度Ra由1.24 μm降至0.542 μm，小孔处表面粗糙度Ra由1.21 μm降至0.437 μm。结论显示固液两相磨粒流加工技术可有效提高被加工喷嘴工件的内表面质量，加工时同一截面的速度存在速度差，速度差的存在利于涡旋的形成，涡旋的存在利于提高磨粒流加工过程的剪切作用，有助于获得高质量的喷嘴小孔内通道表面。